Title of the abstract (max. 2 lines)

<First Author>Surname, name1,*, <Co-Author>2, and <Co-Author>3

* Corresponding Author: email@email.com

1<Affiliation 1: Institution, Address, Country>

2<Affiliation 2: Institution, Address, Country>

3<Affiliation 2: Institution, Address, Country>

Keywords: <max. 5 keywords in 1 line>

1 Page layout

Use A4 paper size (210 x 297 mm) and adjust the margins to those shown in Table 1. The final printed area will be 172 x 252 mm. There is a limit of two pages.

Table 1. Setting Word’s margins.

Margin	mm
Top	25
Bottom	20
Left	20
Right	20

Use a two-column format, and set the spacing between the columns at 8 mm. Do not add any page numbers.

1.1 Formatting the title, authors and affiliations

1.1.1 Formatting the title

The title is set in bold 16-point Arial, justified. The first letter of the title should be capitalised with the rest in lower case.

1.1.2 Formatting author names and author affiliations

The style for the names is First Name, typed in italic 10-point Times, then Last Name, typed in 10-point Times, with a comma after all except the last author, which is separated by comma plus “and”. Do not use academic titles.

Affiliations of authors should be typed in 9-point Times. They should be preceded by a numerical superscript corresponding to the same superscript after the name of the author concerned. Please ensure that affiliations are as full and complete as possible and include the country.
1.2 Formatting the text

The text of your paper should be formatted as follows:

- 10-point Times, Times Roman or Times New Roman.

- The text should be set to single line spacing.

- Paragraphs should be justified.

- The first paragraph after a section or subsection should not be indented; subsequent paragraphs should be indented by 5 mm.

The use of sections to divide the text of the paper is optional and left as a decision for the author. Where the author wishes to divide the paper into sections the formatting shown in Table 2 should be used.

Table 2. Formatting sections, subsections and subsubsections.

Font	Spacing	numbering
Section	12-point Arial bold	6 mm before 3 mm after	1, 2, 3, etc.
subsection	10-point Arial bold	6 mm before 3 mm after	1.1, 1.2, 1.3, etc.
subsubsection	10-point Arial Italic	6 mm before 3 mm after	1.1.1, 1.1.2, 1.1.3, etc.

2 Figures and tables

Figures and tables, as originals of good quality and well contrasted, are to be in their final form, ready for reproduction, pasted in the appropriate place in the text. Try to ensure that the size of the text in your figures is approximately the same size as the main text (10 point). Try to ensure that lines are no thinner than 0.25 point. Embed figures as a vector graphic or high-resolution PNG file with 300 dpi.

Fig. 1. Caption of the Figure 1. Below the figure.

2.1. Captions/numbering

Captions should be typed in 9-point Times. They should be centred above the tables and flush left beneath the figures.

2.2 Positioning

Place the figure as close as possible after the point where it is first referenced in the text. If there is a large number of figures and tables it might be necessary to place some before their text citation. If a figure or table is too large to fit into one column, it can be centred across both columns at the top or the bottom of the page.

2.3 Colour illustrations

You are free to use colour illustrations for the online version of the proceedings. Please make figures and data visualisations accessible to color-blind readers using colour palettes with tonal contrast.

3 Equations and mathematics

Equations should be centred and should be numbered with the number on the right-hand side.

Ts (l,t) = Tg (l,t)	(1)

Ts (l,t) = Tg (l,t) Tb (x   , t) = 0	(2)

Use italics for variables (u) and bold (u) for vectors. The order for brackets should be {[()]}, except where brackets have special significance.

The acknowledgements should be typed in 9-point Times, without title.

Upload your file with a uniform file name including the name of the first author: <Surname_Name>_BCR26.pdf

References

Online references will be linked to their original source, only if possible. To enable this linking extra care should be taken when preparing reference lists.

References should be cited in the text by placing sequential numbers in brackets (for example, [1], [2, 5, 7], [8-10]). They should be numbered in the order in which they are cited. A complete reference should provide enough information to locate the article. References to printed journal articles should typically contain:

• The authors, in the form: initials of the first names followed by last name (only the first letter capitalized with full stops after the initials),

• The journal title (abbreviated),

• The volume number (bold type),

• The article number or the page numbers,

• The year of publication (in brackets).

Authors should use the forms shown in Table 3 in the final reference list.

Table 3. Font styles for a reference to a journal article.

Element	Style
Authors	Normal Initials followed by last name
Journal title	Normal Abbreviated
Book title, Proceedings title	Italic
Volume number	Bold
Page number	Normal
Year	Normal In brackets

Here are some examples:

A. Mecke, I. Lee, J.R. Baker jr., M.M. Banaszak Holl, B.G. Orr, Eur. Phys. J. E 14, 7 (2004)

M. Ben Rabha, M.F. Boujmil, M. Saadoun, B. Bessaïs, Eur. Phys. J. Appl. Phys. (to be published)

Luigi T. De Luca, Propulsion physics (EDP Sciences, Les Ulis, 2009)

F. De Lillo, F. Cecconi, G. Lacorata, A. Vulpiani, EPL, 84 (2008)